High availability for MySQL on Amazon EC2 â€" Part 2 – Setting up the initial instances

This post is the second of a series that started here.

The first step to build the HA solution is to create two working instances, configure them to be EBS based and create a security group for them. A third instance, the client, will be discussed in part 7. Since this will be a proof of concept, I’ll be using m1.small type instances while normally, the mysql host would be much larger. Using another type is trivial. I will assume you are using the command line api tools, on Ubuntu, install “ec2-api-tools”. The use of these tools simplifies the expression of the command compared to the web based console.

Create the security group

The instances involved in the MySQL HA setup will need to be inside the same security group for networking purposes and the help identify them. To create a security simply run this command:

From now, I’ll always assume the EC2_CERT and EC2_PRIVATE_KEY environment variables are setup in your shell. Next, we need to authorize some communications for the security group. I’ll authorize 3306/tcp (MySQL) from hamysql, 694/udp (Heartbeat) from hamysql and 22 (SSH) from everywhere. You can be more restrictive for SSH if you want to.

Launch the instances

Now we can start creating our instances. Since this is only a proof of concept, I’ll built 2 m1.small instances, fell free to use other types. At the time I wrote this, the following AMI seems ok.

So, lauching 2 of these,

I don’t know about you but I don’t like multi-lines output so I wrote a small filter script to on one line the parameters I need separated by a delimiter.

and now we have

which is to my opinion easier to manipulate.

Configuring Heartbeat

Now, let’s configure Heartbeat. The first thing to is to set up the hostname on both host. Heartbeat identifies the host on which it is running by its hostname so that’s mandatory step.

First host:

Second host:

We don’t really need to set /etc/hostname since it is overwritten when the instance is started, even when using EBS based AMI. The next step is to install Heartbeat and Pacemaker on both host, with Ubuntu 10.04, it is very straightforward:

Then we can proceed and configure Heartbeat, Pacemaker will come later. Heartbeat needs 2 configuration files, /etc/ha.d/authkeys for cluster authentication and /etc/ha.d/ha.cf which is the configuration file per say. On both host, the chosen key in the authkeys file must be identical and good way to generate unique one is to run “date | md5sum” and grab a substring from the output.

Also don’t forget to restrict the access rights on the file like:

For the /etc/ha.d/ha.cf file, since EC2 does not support neither broadcast or multicast within the security group, we need to use unicast (ucast) so both files will not be identical. The ucast entry on one host will contain the IP address on the internal network of the other host. On the monitor host, we will have:

and on the hamysql host:

Let’s review briefly the configuration file. First we have setup “autojoin none” that means no host not listed explicitely in the configuration file can join the cluster so we know we have at most 2 members, “monitor” and “hamysql”. Next is the ucast communication channel to reach the other node and the timing parameters. “warntime” is a soft timeout in second that logs the other node is later while “deadtime” is the hard limit after which heartbeat will the consider the other node dead and start actions to restore the service. The “initdead” is just a startup delay to allow host to fully boot before attempting actions and “crm respawn” starts the Pacemaker resources manager. Finally, we have the two “node” declarations” for the cluster members.

So we are done with the configure, time to try if it works. On both hosts, run:

and if everything is right, after at most a minute, you should be able to see both heartbeat processes chatting over the network

We can also use the “crm” tool to query the cluster status.

Install MySQL

For the sake of simplicity, we will just install the MySQL version in the Ubuntu repository by doing:

The package install MySQL has an automatic startup script controlled by init (new to lucid). That’s fine, I will surprise you but Pacemaker will not manager MySQL, just the host running it. I’ll also skip the raid configuration of multiple EBS volumes since it is not the main purpose of this blog series.

EBS based AMI

Others have produce excellent article on how to create EBS based AMI, I will not reinvent the wheel. I followed this one: http://www.capsunlock.net/2009/12/create-ebs-boot-ami.html

Upcoming in part 3, the configuration of the HA resources.