The Backup Cycle - Full Backups¶
Creating a backup¶
To create a backup, run xtrabackup with the
option. You also need to specify the
--target-dir option, which is where
the backup will be stored, if the InnoDB data or log files are not stored in
the same directory, you might need to specify the location of those, too. If the
target directory does not exist, xtrabackup creates it. If the directory does
exist and is empty, xtrabackup will succeed.
xtrabackup will not overwrite existing files, it will fail with operating
system error 17,
To start the backup process run:
$ xtrabackup --backup --target-dir=/data/backups/
This will store the backup at
/data/backups/. If you specify a
relative path, the target directory will be relative to the current directory.
During the backup process, you should see a lot of output showing the data
files being copied, as well as the log file thread repeatedly scanning the log
files and copying from it. Here is an example that shows the log thread
scanning the log in the background, and a file copying thread working on the
160906 10:19:17 Finished backing up non-InnoDB tables and files 160906 10:19:17 Executing FLUSH NO_WRITE_TO_BINLOG ENGINE LOGS... xtrabackup: The latest check point (for incremental): '62988944' xtrabackup: Stopping log copying thread. .160906 10:19:18 >> log scanned up to (137343534) 160906 10:19:18 Executing UNLOCK TABLES 160906 10:19:18 All tables unlocked 160906 10:19:18 Backup created in directory '/data/backups/' 160906 10:19:18  Writing backup-my.cnf 160906 10:19:18  ...done 160906 10:19:18  Writing xtrabackup_info 160906 10:19:18  ...done xtrabackup: Transaction log of lsn (26970807) to (137343534) was copied. 160906 10:19:18 completed OK!
The last thing you should see is something like the following, where the value
<LSN> will be a number that depends on your system:
$ xtrabackup: Transaction log of lsn (<SLN>) to (<LSN>) was copied.
Log copying thread checks the transactional log every second to see if there were any new log records written that need to be copied, but there is a chance that the log copying thread might not be able to keep up with the amount of writes that go to the transactional logs, and will hit an error when the log records are overwritten before they could be read.
After the backup is finished, the target directory will contain files such as
the following, assuming you have a single InnoDB table
test.tbl1 and you
are using MySQL’s innodb_file_per_table option:
$ ls -lh /data/backups/ total 182M drwx------ 7 root root 4.0K Sep 6 10:19 . drwxrwxrwt 11 root root 4.0K Sep 6 11:05 .. -rw-r----- 1 root root 387 Sep 6 10:19 backup-my.cnf -rw-r----- 1 root root 76M Sep 6 10:19 ibdata1 drwx------ 2 root root 4.0K Sep 6 10:19 mysql drwx------ 2 root root 4.0K Sep 6 10:19 performance_schema drwx------ 2 root root 4.0K Sep 6 10:19 sbtest drwx------ 2 root root 4.0K Sep 6 10:19 test drwx------ 2 root root 4.0K Sep 6 10:19 world2 -rw-r----- 1 root root 116 Sep 6 10:19 xtrabackup_checkpoints -rw-r----- 1 root root 433 Sep 6 10:19 xtrabackup_info -rw-r----- 1 root root 106M Sep 6 10:19 xtrabackup_logfile
The backup can take a long time, depending on how large the database is. It is safe to cancel at any time, because xtrabackup does not modify the database.
The next step is getting your backup ready to be restored.
Preparing a backup¶
After making a backup with the
--backup option, you need need to
prepare it in order to restore it. Data files are not point-in-time consistent
until they are prepared, because they were copied at different times as the
program ran, and they might have been changed while this was happening.
If you try to start InnoDB with these data files, it will detect corruption and
stop working to avoid running on damaged data. The
makes the files perfectly consistent at a single instant in time, so you can run
InnoDB on them.
You can run the prepare operation on any machine; it does not need to be on the originating server or the server to which you intend to restore. You can copy the backup to a utility server and prepare it there.
Note that Percona XtraBackup 8.0 can only prepare backups of MySQL 8.0, Percona Server for MySQL 8.0, and Percona XtraDB Cluster 8.0 databases. Releases prior to 8.0 are not supported.
During the prepare operation, xtrabackup boots up a kind of modified embedded InnoDB (the libraries xtrabackup was linked against). The modifications are necessary to disable InnoDB standard safety checks, such as complaining about the log file not being the right size. This warning is not appropriate for working with backups. These modifications are only for the xtrabackup binary; you do not need a modified InnoDB to use xtrabackup for your backups.
The prepare step uses this “embedded InnoDB” to perform crash recovery on the
copied data files, using the copied log file. The
prepare step is very
simple to use: you simply run xtrabackup with the
and tell it which directory to prepare, for example, to prepare the previously
taken backup run:
$ xtrabackup --prepare --target-dir=/data/backups/
When this finishes, you should see an
InnoDB shutdown with a message such
as the following, where again the value of LSN will depend on your
InnoDB: Shutdown completed; log sequence number 137345046 160906 11:21:01 completed OK!
All following prepares will not change the already prepared data files, you’ll see that output says:
xtrabackup: This target seems to be already prepared. xtrabackup: notice: xtrabackup_logfile was already used to '--prepare'.
It is not recommended to interrupt xtrabackup process while preparing backup because it may cause data files corruption and backup will become unusable. Backup validity is not guaranteed if prepare process was interrupted.
Restoring a Backup¶
Backup needs to be prepared before it can be restored.
$ xtrabackup --copy-back --target-dir=/data/backups/
If you don’t want to use any of the above options, you can additionally use rsync or cp to restore the files.
The datadir must be empty before restoring the backup. Also it’s important to note that MySQL server needs to be shut down before restore is performed. You cannot restore to a datadir of a running mysqld instance (except when importing a partial backup).
Example of the rsync command that can be used to restore the backup can look like this:
$ rsync -avrP /data/backup/ /var/lib/mysql/
You should check that the restored files have the correct ownership and permissions.
As files’ attributes will be preserved, in most cases you will need to change
the files’ ownership to
mysql before starting the database server, as they
will be owned by the user who created the backup:
$ chown -R mysql:mysql /var/lib/mysql
Data is now restored and you can start the server.